Great Midwest Yacht
sail boat
sail boat

MISCELLANEOUS

Compass
 Use to read the shifts. Non-racers can use for conventional navigation

Mounted compass assembly  - mount between stanchions just below forward grating
teak, Ritchie SS2000
GF691
$417.00
teak, Ritchie SS1000
GF692
$270.00
teak, Ritchie RU90
GF693
$182.00
mahogany, Ritchie SS2000
GF591
$407.00
mahogany, Ritchie SS1000
GF592
$260.00
mahogany, Ritchie RU90
GF593
$172.00
Compasses 
Ritchie 2000, dial diameter 4 1/2"
GB833
$330.00
Ritchie 1000, dial diameter 3 3/4"
GB832
$198.00
Ritchie RU90, dial diameter 3"
GB830
$110.00
Compass mounts  - supply your own compass
teak, for Ritchie SS2000
GE691-1
$87.00
teak, for Ritchie RU90, SS1000
GE691
$72.00
mahogany, for Ritchie SS2000
GE591-1
$77.00
mahogany, for Ritchie RU90, SS1000
GE591
$62.00
Hazard course computer   - translate the compass readings into lift and header information
GB841
$15.00

Fiberglass

Bilge stiffener kit  - includes foam stiffener strips, bedding and covering fiberglass, requires polyester resin.Stiffen the bilges of your soft fg boat
GB820
$160.00
Stern tanks, pair  - includesbedding and covering fiberglass, requires polyester resin. Requires fitting. Add flotation tanks to yourearly fg hull
GE020
$160.00
Seat tanks, pair  - includes bedding and covering fiberglass, unmounted inspection ports, chain plates. Will require new cross- thwart. Replace old leaky, swayback seats in older fg hulls.
GE030
$725.00
Seat horn repair kit  - fixes the deformation of the forward face of seat tank on some fg hulls
GC720
$52.00

Flotation
 1 to 2 lb styrofoam sticks to provide TCA-required positive flotation in fiberglass hulls

Sticks  - bundle of 25 pcs. Fills inside of tanks on fg hulls. 3 bundles needed for one boat.
GE845
$49.50
Shaped blocks  - hot-wire-shaped to fit wood hulls. For durability, will need coating or bagging
full set, includes packing for shipping
GA015
$635.00
full set
GA015-1
$565.00
bow
GE840
$215.00
seat, 4 pc
GE841
$175.50
forward pcs, set of 2
GE844
$108.35
aft pcs, set of 2
GE842
$67.25
stern, 2-piece set. Also fits older fg hulls without stern tanks
GE843
$174.00

Hull attachments
 The pieces and parts that attach to exterior of the hull

Bailer  - Anderson Elvstrom 'Super max'. Interior plate 3 x 5 1/4", hole through hull 2 1/8 x 4 11/32"
GB020
$149.00
Centerboard gasket  - two-piece, heavy-duty folded sailcloth
GB825
$34.00
Gudgeon, ea  - heavy-duty double-loop strap with 4 mounting holes. Fits 3/8" pintles
RL490
$13.25
Keel strip  - 1/2" wide aluminum half round
full set
GE820
$93.50
full set with fasteners
GC820
$69.50
stem - runs down stem and extends 8" aft of stem
GE821
$13.50
stem with fasteners
GE821-1
$14.10
forward - runs from stem piece to 2" fwd of CB trunk
GE822
$22.60
trunk - holds the CB gasket in place, pair
GE823
$38.10
aft - from CB trunk to transom
GE824
$19.50
5200 sealant  - use to seal keel-strip screws. Silicone does NOT work
GB771
$14.47

Lifting
 Hoist your boat safely

Lifting bridle assembly  - 3/8" dacron. With 2 stainless S-hooks for attachment to forward grating and D-shackle for aft attachment. Grating hardware is included, aft hardware is not
GF820
$52.25
bridle only
GF821
$45.40
Lifting hardware  - for permanent attachment to theboat
forward grating hardware for lifting bridle
GF822
$11.25
aft lifting claw for GMW, late D&M
XE179
$16.25
4 hole eye strap for early D&M. Mounts to trunk angled aft cover
RL314B
$2.65

MIscellaneous

Inspection port  - 4", includes fasteners
GC855
$9.00
Closed-end aluminum pop rivets use to install inspection ports, attachment of boom end castings
GB722
$0.30
Aluminum washer use inside tank as pop-rivet backer when installing inspection ports
GB723
$0.05
Quick-release pin  - 3/16", solid hardened-stainless pin with ball detent at one end. Caution - the hollow, center-push quick pins will break under shroud loads
medium lenght, attaches shroud to chain plate on seat
GB005
$4.25
short length, attaches shroud to shroud extender or Staymaster
GB013
$3.95
Shroud plate bushings  - needed if you're removing shroud plates for varnishing or replacing rails, pair
GB016
$3.75
Replacement pad for spinnaker guy hook, pair
GB310
$3.75

Spinnaker pole

Complete pole  - 1 1/4" aluminum tubing, stainless steel and bronze end fittings, and eyestrap for topping lift attachment
GF130
$200.00
pole only with one end plugged
XF131
$52.00
pole end with fasteners, ea
RF677F
$58.75
Spinnaker pole-end repair parts  - pin plunger, spring, ring
RF677-1
$7.75

Trailering

Thistle trailer  - Wesco. Galvanized, low-to-the-ground, 5 support rollers
GF993
$2675.00
Trailer center bunk  - laminated, pressure-treated and padded. Curved to match contour of hull
GC994
$275.00
wood only
GB994
$185.00
Trailering mast support  - secures to aft grating
GE830
$30.00
Trailering tie-down strap 
GB980
$17.70

Traveler

Traveler track and car  - includes end stops and fasteners. New boats use H2729 for car. Other choices below
GC330-1
$271.80
traveler track, includes end stops and fasteners
H2720-1
$87.05
end stops for traveler track
H173
$8.35
Traveler car  - all cars are captive-ball style, none fit the old-style track
with eye strap for mainsheet block and 2 sheaves for traveler control
H2729
$184.75
ti-lite, mainsheet block needed is Harken H2651.
H2733
$150.80
pivoting shackle for mainsheet block. Control tangs for attaching traveler blocks or lines
H2754
$183.05
Traveler car balls  - use to rebuild older-style Harken (loose ball) traveler car.
H177
$12.85
Traveler profile template  - reduce the height of your transom by removing the wood over the tiller hole. Traveler track will bend to this curve during installation
GG300
$5.00